{"id":3336,"date":"2026-09-29T01:45:28","date_gmt":"2026-09-28T17:45:28","guid":{"rendered":"http:\/\/www.innvant.com\/blog\/?p=3336"},"modified":"2026-09-29T01:45:28","modified_gmt":"2026-09-28T17:45:28","slug":"what-are-the-differences-between-submerged-arc-and-tig-welded-stainless-steel-parts-43cf-890177","status":"publish","type":"post","link":"http:\/\/www.innvant.com\/blog\/2026\/09\/29\/what-are-the-differences-between-submerged-arc-and-tig-welded-stainless-steel-parts-43cf-890177\/","title":{"rendered":"What are the differences between submerged – arc and TIG – welded stainless steel parts?"},"content":{"rendered":"

If you\u2019ve ever sourced stainless steel welded parts for industrial equipment, food processing machinery, or architectural infrastructure, you\u2019ve probably encountered two common welding methods for stainless steel: submerged arc welding (SAW) and TIG welding. As someone who\u2019s run a stainless steel welded parts supplier for 12 years\u2014walking the production floor, troubleshooting weld defects with my team, and working directly with clients to match the right method to their project\u2014I can tell you that choosing between these two isn\u2019t just about preference; it\u2019s about material integrity, precision, cost, and long-term performance. Let\u2019s break down the key differences, rooted in real-world production and client needs, so you can make a more informed choice for your next project. Stainless Steel Welded Parts<\/a><\/p>\n

<\/p>\n

First, let\u2019s start with the basics to ground this. Stainless steel is prized for its corrosion resistance, strength, and aesthetic appeal, but its high chromium and nickel content makes it trickier to weld than carbon steel. If heat isn\u2019t controlled properly, you can get things like grain boundary sensitization (which kills corrosion resistance) or warping from uneven thermal expansion. Both SAW and TIG are arc welding processes, but their heat delivery, shielding methods, and applications are night and day. Let\u2019s dive into each core difference, with examples from parts we\u2019ve shipped to automotive component manufacturers and food processing equipment makers last year.<\/p>\n

Heat Input and Weld Penetration: Where SAW Dominates for Thick, High-Volume Parts
\nSubmerged arc welding is exactly what it sounds like: the arc is completely submerged under a granular flux, which melts to form a protective slag layer over the weld. This flux does two big things: it shields the weld from atmospheric contaminants (oxygen, nitrogen, which cause porosity), and it delivers a super high, concentrated heat input. We\u2019ve used SAW for everything from \u00bd-inch thick 304 stainless steel tank shells for beverage storage to structural support beams for chemical processing units. The heat penetration here is deep\u2014we can get full joint penetration on parts up to 2 inches thick in a single pass, which is a game-changer for high-volume orders.<\/p>\n

Last quarter, a client in the water treatment industry came to us needing 40 identical 6-foot-long 316 stainless steel flanges that would hold a pressure vessel operating at 150 PSI. We priced out both SAW and TIG, and the TIG process would have required three separate passes, multiple pre-heat steps, and taken 2x longer per part. SAW, by contrast, did the weld in one 90-second pass per flange, with consistent penetration across all 40 units. The tradeoff here is that SAW\u2019s heat input is so high that it creates a larger heat-affected zone (HAZ)\u2014the area of base metal adjacent to the weld that\u2019s been altered by heat. For thin-gauge parts, that HAZ can cause warping, and for sensitive grades like 316L, excessive heat can lead to chromium carbide precipitation, which reduces corrosion resistance. We never recommend SAW for parts thinner than 1\/8 inch or for applications where tight corrosion resistance is non-negotiable, like food processing piping.<\/p>\n

TIG Welding: Precision for Thin, Critical, Aesthetic Parts
\nTungsten inert gas welding, or TIG, is the process you see in high-detail metal work: a non-consumable tungsten electrode delivers an arc, and the weld is shielded by an inert gas (usually argon) that flows through the torch, with no flux involved. That lack of flux is key here\u2014no slag to clean up, no risk of flux inclusions, which makes TIG perfect for parts where surface finish and precision matter more than extreme thickness.<\/p>\n

We use TIG for 90% of our custom low-volume orders, like small-batch stainless steel components for craft brewery equipment (think beer line manifolds that come into contact with beer and cleaning chemicals) and medical device parts, where even a tiny weld defect can lead to product failure. Last month, a startup making portable dialysis equipment came to us with a prototype order for 12 1-inch-long 0.04-inch thick 304 stainless steel fluid lines. TIG was the only viable process here: SAW would have burned through the thin metal, and the large HAZ would have made the lines too brittle to flex during use. The tradeoff with TIG is that it\u2019s a slower, more labor-intensive process\u2014each weld requires a skilled technician to manually feed filler wire, adjust gas flow, and control heat. For that same set of 40 flanges I mentioned earlier, TIG would have cost the client 3x more and taken twice as long to ship, which is why SAW made sense for their high-volume, high-pressure application.<\/p>\n

Material Compatibility: Matching Process to Stainless Steel Grade
\nAnother big difference is how each process interacts with different stainless steel grades. 304 and 316, the most common grades, work well with both, but specialty grades like duplex stainless steel or high-alloy 904L often require TIG because of tighter heat controls. Duplex has a balanced ferritic-austenitic structure, and excessive heat from SAW can throw that balance off, reducing toughness and corrosion resistance. We had a client building a marine platform in the Gulf Coast last year that needed 10 duplex stainless steel mooring cleats; TIG was the only process that maintained the duplex\u2019s mechanical properties, even though it took longer than SAW would have.<\/p>\n

For 316L, the low-carbon variant used for medical and food applications, TIG\u2019s lower, more controlled heat input avoids sensitization\u2014 the formation of chromium carbides at grain boundaries that make the steel prone to rust in harsh environments. SAW can work for 316L too, but we always add a post-weld heat treatment step to counteract that, which adds cost and time. For parts that go into food or pharmaceutical use, that extra post-treatment might be required anyway, so TIG is often more streamlined and lower-risk for those applications.<\/p>\n

Cost and Lead Time: Volume vs. Custom
\nIf you\u2019re sourcing stainless steel welded parts, cost is almost always a factor, and the split between SAW and TIG is clear here. SAW is highly automated, so labor costs are a fraction of TIG\u2019s, especially for long, continuous welds. For high-volume orders, SAW can cut per-part costs by 40-60% compared to TIG, with consistent quality when controlled properly. Lead times are also shorter: a 100-part order of tank shells from SAW can ship in 7 days, while the same order from TIG would take 14 days, sometimes longer if parts need post-weld finishing.<\/p>\n

But don\u2019t write off TIG for cost reasons\u2014for low-volume, custom parts, TIG\u2019s precision means less rework. We\u2019ve had clients come to us after using a competitor\u2019s SAW welds on custom architectural handrails, only to find porosity or uneven welds that required grinding and polishing, adding hundreds of dollars in rework costs. TIG welds are clean from the start, so for small orders, the initial cost is often offset by no rework. That said, SAW\u2019s automation means fewer operator errors, so for consistent, high-volume parts, the risk of defects is lower with SAW, as long as the weld parameters are set correctly.<\/p>\n

Surface Finish and Post-Processing Needs
\nOne of the most noticeable differences is surface finish. SAW leaves a thick slag layer that requires grinding, chipping, and cleaning before any finishing (polishing, passivation, painting). We\u2019ve had clients who order SAW-welded parts and underestimate the post-processing time; a 12-inch SAW weld might take 30 minutes to clean up, while a TIG weld of the same size takes 5 minutes, with less grinding needed because the weld is cleaner and more uniform.<\/p>\n

Aesthetic parts, like the stainless steel trim for a luxury elevator or a commercial oven door, almost always use TIG because SAW\u2019s slag and large weld bead are hard to polish evenly. We did a set of TIG-welded oven doors for a major appliance brand last year; the welds blended seamlessly with the base metal, no grinding required, while a SAW weld would have left a visible, uneven line that would have been unsightly. For parts that need to be passivated (a chemical process to boost corrosion resistance), TIG\u2019s cleaner weld means passivation works more evenly, reducing the chance of discoloration or uneven resistance.<\/p>\n

Common Misconceptions We See as Suppliers
\nOver the 12 years I\u2019ve been in this business, I hear a lot of myths about these two processes. The biggest one is that TIG is always higher quality. That\u2019s not true\u2014for thick, high-pressure parts, SAW can produce welds with equal or better penetration than TIG, as long as it\u2019s done by a certified technician. Last year, we had a third-party inspector test SAW welds on a 2-inch thick 304 stainless steel pressure vessel, and they passed all pressure and corrosion tests, with no defects. The myth comes from SAW\u2019s reputation for thicker weld beads, which can look less precise, but that\u2019s a cosmetic, not a functional, issue.<\/p>\n

Another myth is that TIG is only for thin parts. We do TIG welds on parts up to 1 inch thick for specialty applications, like high-pressure gas lines for aerospace, where precision and no contamination are critical. But even then, it takes more time and labor than SAW would for the same thickness, so it\u2019s reserved for use cases where the extra precision is necessary.<\/p>\n

Which One Should You Choose?
\nAt the end of the day, the right process depends on three factors: your part\u2019s thickness and size, its application (corrosion resistance, pressure, aesthetic needs), and your order volume. If you need thick, high-volume parts like tank shells, structural beams, or flanges, SAW is the way to go\u2014it\u2019s cost-effective, fast, and delivers consistent penetration for those applications. If you need thin, custom, high-precision parts like medical components, food piping, or aesthetic parts like handrails or trim, TIG is the better choice for its precision, low heat input, and clean finish.<\/p>\n

One thing I always tell clients is to work with a supplier that has experience with both processes, not just one. We\u2019ve seen clients get stuck choosing a process that doesn\u2019t fit their needs because their only supplier only offers TIG or only offers SAW, not both. For example, a client recently came to us with a project that required a large tank shell (for which SAW was ideal) paired with small custom piping connections (for which TIG was better). Instead of having to source from two different suppliers, we were able to do the entire project in-house, ensuring consistent quality across all parts.<\/p>\n

<\/p>\n

If you\u2019re working on a stainless steel welded parts project and aren\u2019t sure which process is right for you, reach out to our team to discuss your needs. We\u2019ll walk you through the pros and cons, share examples of similar projects we\u2019ve completed, and help you find the most cost-effective, high-quality solution for your application. Don\u2019t let process missteps lead to defects, delays, or extra costs down the line\u2014let\u2019s chat about your project today.<\/p>\n

Stainless Steel Products<\/a> References:<\/p>\n

    \n
  1. Lincoln Electric. Submerged Arc Welding for Stainless Steel: Process, Applications, and Best Practices.<\/li>\n
  2. AWS A5.9: Standard Specification for Stainless Steel Welding Electrodes and Rods.<\/li>\n
  3. TIG Welding Institute. Precision Welding for Thin-Gauge Stainless Steel Components.<\/li>\n
  4. ASME Boiler and Pressure Vessel Code, Section IX: Welding Qualifications.<\/li>\n
  5. Stainless Steel Fabricators Association. Guide to Welding Processes for 300 and 400 Series Stainless Steel.<\/li>\n<\/ol>\n
    \n

    Qingzhou Foren Water Treatment Equipment Co., Ltd.<\/a><\/p>\n

    Address: No.999 Haidai North Road, Economic development Zone, Qingzhou City, Shandong Province
    E-mail: alice@forenwater.com
    WebSite:     https:\/\/www.forenwater.com\/<\/a><\/p>\n","protected":false},"excerpt":{"rendered":"

    If you\u2019ve ever sourced stainless steel welded parts for industrial equipment, food processing machinery, or architectural … What are the differences between submerged – arc and TIG – welded stainless steel parts?<\/span>Read more<\/a><\/p>\n","protected":false},"author":20,"featured_media":3336,"comment_status":"closed","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[1],"tags":[3299],"class_list":["post-3336","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-industry","tag-stainless-steel-welded-parts-403e-893f80"],"_links":{"self":[{"href":"http:\/\/www.innvant.com\/blog\/wp-json\/wp\/v2\/posts\/3336","targetHints":{"allow":["GET"]}}],"collection":[{"href":"http:\/\/www.innvant.com\/blog\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"http:\/\/www.innvant.com\/blog\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"http:\/\/www.innvant.com\/blog\/wp-json\/wp\/v2\/users\/20"}],"replies":[{"embeddable":true,"href":"http:\/\/www.innvant.com\/blog\/wp-json\/wp\/v2\/comments?post=3336"}],"version-history":[{"count":0,"href":"http:\/\/www.innvant.com\/blog\/wp-json\/wp\/v2\/posts\/3336\/revisions"}],"wp:featuredmedia":[{"embeddable":true,"href":"http:\/\/www.innvant.com\/blog\/wp-json\/wp\/v2\/posts\/3336"}],"wp:attachment":[{"href":"http:\/\/www.innvant.com\/blog\/wp-json\/wp\/v2\/media?parent=3336"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"http:\/\/www.innvant.com\/blog\/wp-json\/wp\/v2\/categories?post=3336"},{"taxonomy":"post_tag","embeddable":true,"href":"http:\/\/www.innvant.com\/blog\/wp-json\/wp\/v2\/tags?post=3336"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}